Линии непрерывной вулканизации и
электронной сшивки

NOKIA-MAILLEFER 150 mm Single Layer Rubber CV Line

FULLY MODERNIZED - AVAILABLE FROM FACTORY SHUTDOWN

Complete rubber insulation/sheathing line based on 150 mm NOKIA extruder with steam curing in pressure tube.

Tube is about 65 m long (28.5 m steam)

It can be used for rubber insulation of conductors typically from 25 to 400 mmІ.
Max core diameter 6 - 23.8 mm. Max cable dia : 60 mm.
Thickness of rubber insulation or sheath of 6 mm max.

Line can run linear speed of 54 m/min max.

Pay-offs and take-ups are 2200 mm diameter.

Line has just been modernized.

It has :
- NEW TROESTER Sag Control
- NEW Electric & electronic
- NEW Stainless tube
- NEW Water/Steam control

Rest of equipment was completeley reconditioned.

Equipment is still in a European factory ceasing operations.
Подробнее

добавлено 10.03.2021 в 10:50

В связи с прекращением производства кабельно-проводниковой продукции, ООО "Азовская Кабельная Компания" реализует основное и вспомогательное технологическое оборудование.

Подробнее

Подробнее

FULLY RECONDITIONED Horizontal accumulator.

Diameter of pulleys : 1.400 mm
Round grooves suitable for cables : 5-60 mm

Number of pulleys : 5+5

Dimensions : : 10.000 x 1.300 x 1.800 mm (Lxlxh)

Motor : 7 kW.

Подробнее

RECONDITIONED NOKIA-MAILLEFER Extruder Model NMT 150-24D
Screw dia : 150 mm
L/D Ratio : 24
Number of zones : 6 Zone
Cooling with oil.
Driven by : DC motor

NEW Screw :
For hard & sticky rubber (see screw detailed drawing at the bottom of this page)

NEW Thermorgulators :
- For screw
- For cylinder
- For head

X-head available.

Подробнее

SIKORA X-Ray Eccentricity Control
Model 8000 NXT
With control & cooling system

Подробнее

NEW individual water cooling system with tank, heat exchanger & chillers.

Подробнее

Tube is new & made of three sections :
- 28.5 m Steam vulcanization pipe 219 mm
- 37 m Water pipe 150 mm
- End seal with hydraulic clamp and dryer

Additionnally, tube is equipped with
- TROESTER SAG Control, Model TRISAG-150
- Automatic steam/water level control with cabinet
- Individual cooling system
- Automatic Water Discharge Unit
- Tanks
- 2x CALPEDA Pumps with motor ABB

Подробнее

FULLY RECONDITIONED Belt Wrap Pulling Capstan

Diameter : 3.000 mm
Driven by : 18.5 kW DC motor with 4 speed gearbox


Подробнее

Two NEW portal take-ups suitable for bobbins :

Diameter : 1400-2200 mm
OAW : 810-1100 mm
Bore : 80 mm
Weight : 7.000 kg

Portal/self traversing.
Max speed : 180 m/min - 4 speeds (AC motor - 8.92 kW)
Max cable dia : 60 mm

Подробнее

NOKIA-MAILLEFER Triple Layer Rubber CV Line (Ref : TJJ4QF)

Delivery includes :

- 2 x ACC Portal Pay-offs 2200 mm - 7.000 kg
- 1 x NOKIA Horizontal Accumulator
- 1 x NOKIA Belt Wrap Capstan 2.000 mm
- 1 x NOKIA 150 mm 18 D Extruder with 190 kW DC motor
- 1 x BAICHENG 90 mm 18 D Extruder
- 1 x BAICHENG 65 mm 18 D Extruder
- 4 x BAICHENG Extrusion X-heads
* 1 x Single Layer for Rubber
* 1 x Double Layer for Rubber
* 1 x Triple Layer for Rubber
* 1 x Triple Layer for XLPE
- 1 x Many toolings
- Extra screws
- 1 x SIKORA x-ray 800 NXT Eccentricity Control on Telescopic
- 1 x NOKIA SAG Control
- 1 x 28.5 m Steam vulcanization pipe 219 mm
- 1 x 5.5 m Separating section 219 mm
- 1 x 27.5 m Cooling pipe 150 mm
- 1 x End seal with hydraulic clamp and dryer
- 1 x BAICHENG Pulling Caterpillar
- 1 x Deviation pulley
- 1 x 25 m Cold water canal
- 1 x Helping Caterpillar 800 kg
- 1 x Sparker
- 1 x Powder coating
- 1 x Cable cutter
- 2 x NOKIA Self-traversing Take-ups 2200 mm
- 1 x Electrical cabinet with Siemens S7 PLC & Parker drives

Подробнее

Horizontal accumulator.

Diameter of pulleys : 1.600 mm
Round grooves.

Number of pulleys : 5+6

Dimensions : 15.100 x +/- 1.300 x 2.125 mm (Lxlxh)

Подробнее

Belt Wrap Capstan

Diameter : 2.000 mm
Driven by : 6.8 kW DC motor with 4 speed gearbox, 3.75-7.5-15.0-30.0 m/min.

Max pulling force : 20 kN

Подробнее

NOKIA Main Extruder
Screw dia : 150 mm
L/D Ratio : 18
Number of zones : 4 Zones
Driven by : DC motor 190 kW

Thermorgulators :
- For screw
- For cylinder
- For head

Two screws available for : Rubber & XLPE

Подробнее

Baicheng Secondary Extruder for External Layer
Screw dia : 90 mm
L/D Ratio : 18
Number of zones : 4 Zones
Driven by : DC motor 75 kW

Cylinder material : 38CrMoA1A / heat treated 0.4-0.6 mm (>= HV950)
Screw material : 38CrMoA1A / heat treated 0.4-0.6 mm (>= HV850)

Two screws available for : Rubber & XLPE

Подробнее

Baicheng Secondary Extruder for Internal Layer
Screw dia : 65 mm
L/D Ratio : 18
Number of zones : 4 Zones
Driven by : DC motor 37 kW

Cylinder material : 38CrMoA1A / heat treated 0.4-0.6 mm (>= HV950)
Screw material : 38CrMoA1A / heat treated 0.4-0.6 mm (>= HV850)

Two screws available for : Rubber & XLPE

Подробнее

Four X-heads available :
- 1 x Single Layer for Rubber
- 1 x Double Layer for Rubber, In : max 55 mm // Out : max 70 mm
- 1 x Triple Layer for Rubber, In : 7-35 mm // Out : 15-75 mm
- 1 x Triple Layer for XLPE, In : 7-35 mm // Out : 15-75 mm

Подробнее

Tube consists in :
- 1 x 28.5 m Steam vulcanization pipe 219 mm
- 1 x SAG Control
- 1 x 5.5 m Separating section 219 mm
- 1 x 27.5 m Cooling pipe 150 mm
- 1 x End seal with hydraulic clamp and dryer

Additionnally, tube is equipped with
- Steam/water level control with cabinet
- Individual cooling system
- Automatic Water Discharge Unit
- Tanks
- High-pressure pumps

Подробнее

BAICHENG Pulling Caterpillar

Gripping : 2.900 mm
Pulling force : 3.200 kg
Driven by : 11 kW DC motor with 4 speed gearbox (2.3-90 m/min)

Подробнее

Helping caterpillar Maillefer.
Pulling force : 800 kg.

Подробнее

5-25 kV Spark Tester

Подробнее

Clamping & cutting device

Подробнее

NOKIA Column type take-ups suitable for bobbins :

Diameter : 1400-2200 mm
OAW : 810-1100 mm
Bore : 80 mm
Weight : 7.000 kg

Column type/self traversing.

Подробнее

INP E-Beam X-Linking Line for PE & HFFR, Cables 5-35 mm, Model ELV-2 (ref C2) (Ref : XFBQ3V)



WWW.WICSE.COM

FACTORY SHUTDOWN - STILL INSTALLED

E-beam X-linking line based ELV2 high voltage electron accelerator manufactured by INP (Institute of Nuclear Physics).

Line is operating inside concrete/shielded room.

ELV-2 is suitable for X-linking one cable a time, diameter 5-35 mm.
Can process typically 4 mm of PE max & 3 mm of HFFR max.

Speedwise, installation can run 8 to 40 m/min max depending cable size.

System was modernized electronically.

A new electronic high-frequency power supply has been installed with new control cabinet.
PLC and HMI are from BAZIS (Russia)

Take-up and pay-off were added new.

Подробнее

INP E-Beam X-Linking Line for PE & HFFR, Cables 5-35 mm, Model ELV-2 (ref C2) (Ref : XFBQ3V)


Scope of delivery consists in :
- Braked cantilever pay-off 800-1.400 mm
- Multi-pass pulleys
- ELV2 E-beam accelerator
- Vacuum pump
- Pulling capstan
- Cantilever take-up 800-1.400 mm
- Lifting system
- Electrical control

Подробнее

NEW

Cantilever pay-off
Dia : 800-1.400 mm
Brake type

Hydraulic lifting - Manual pintles

Подробнее

Modernized electric/electronic.

A new electronic high-frequency power supply has been installed.
Also new vacuum controller.

All panels are new with PLC and HMI from BAZIS (Russia).

Подробнее

INP E-Beam X-Linking Line for PE & HFFR, Section 2.5-25 mmІ, Model ELV-1 (ref C4) (Ref : LC2AAL)

FACTORY SHUTDOWN - STILL INSTALLED

E-beam X-linking line based ELV1 high voltage electron accelerator manufactured by INP (Institute of Nuclear Physics).

Line is operating inside concrete/shielded room.

ELV-1 is suitable for X-linking one conductor a time, x-section typically 2.5-25 mmІ (smaller possible with less multi turns)
Can process typically 2 mm of PE max & 1.5 mm of HFFR max.

Speedwise, installation can run 30 to 100 m/min max depending conductor size.

System was modernized electronically.

A new electronic high-frequency power supply has been installed with new control cabinet.
PLC and HMI are from BAZIS (Russia)

Take-up and pay-off were added new.

Подробнее

NEW

Cantilever take-up
Dia : 800-1.400 mm
Uhing traversing

Hydraulic lifting - Manual pintles

Подробнее

INP E-Beam X-Linking Line, Model ELV-2 (ref C1)
for PE (4 mm) & HFFR (3 mm), 15-60 mm
1-25 m/min

FACTORY SHUTDOWN - STILL INSTALLED

E-beam X-linking line based ELV2 high voltage electron accelerator manufactured by INP (Institute of Nuclear Physics).

Line is operating inside concrete/shielded room.

ELV-2 is suitable for X-linking one cable a time, diameter 15-60 mm.
Can process typically 4 mm of PE max & 3 mm of HFFR max.

Speedwise, installation can run 1 to 25 m/min max depending cable size.

Scope of delivery consists in :
- Portal pay-off 1.400-2.200 mm
- Multi-pass pulleys
- ELV2 E-beam accelerator
- Vacuum pump
- Pulling capstan + Caterpillar
- Portal take-up 1.400-2.200 mm
- Lifting system
- Electrical control

Подробнее

INP E-Beam X-Linking Line, Model ELV-1 (ref C5)
for PE (2 mm) & HFFR (1.5 mm), 0.5-6 mmІ
50-150 m/min

ACTORY SHUTDOWN - STILL INSTALLED

E-beam X-linking line based ELV1 high voltage electron accelerator manufactured by INP (Institute of Nuclear Physics).

Line is operating inside concrete/shielded room.

ELV-1 is suitable for X-linking one conductor a time, x-section typically 0.5-6 mmІ
Can process typically 2 mm of PE max & 1.5 mm of HFFR max.

Speedwise, installation can run 50 to 150 m/min max depending conductor size.

Scope of delivery consists in :
- Braked cantilever pay-off 400-800 mm
- Multi-pass pulleys
- ELV2 E-beam accelerator
- Vacuum pump
- Pulling capstan
- Cantilever take-up 400-800 mm
- Lifting system
- Electrical control

Подробнее

INP E-Beam X-Linking Line, Model ELV-2 (ref C3)

Подробнее